Hinta, verot, tullimaksut, toimitus, B2B
Tuotteet lähetetään EU:sta. Näytetyt hinnat sisältävät arvonlisäveron (VAT), jos sovellettavissa. EU:n ulkopuolelle toimitettaviin tilauksiin voidaan soveltaa paikallisia veroja, tullimaksuja, tuonnin VAT-maksua tai kuljetusyhtiön käsittelymaksuja.
Nähdäksesi käytettävissä olevat toimitustavat ja -kulut, lisää tuotteet ostoskoriin, siirry kassalle ja syötä toimitusosoitteesi.
EU:ssa VAT-rekisteröidyt yritykset voivat ostaa tuotteet 0 % VAT-verolla.
Ostaaksesi B2B-asiakkaana sinun täytyy ensin rekisteröidä yrityksesi asiakkaaksi.
Kuvaus
A heavy-duty stainless steel optic plate that mounts a Leupold DeltaPoint Pro or EOTech EFLX on Glock Gen 6 ORS slides.
The OPF-G6, DPP replaces the polymer insert of the Glock Gen 6 Optic Ready System with a plate milled from 17-4 stainless steel. Its underside is contoured to fill the spindle-shaped cavity in the ORS pocket and a relief at the rear engages the slide's locking tab, so the plate cannot rotate or shift.
Four steel lugs support the four lug holes of the DeltaPoint Pro footprint and do not give under load the way a polymer insert can, keeping recoil load off the screws. The plate sits flush with the top of the ORS pocket so the sight is not raised.
Key features
- 17-4 stainless steel — Milled from 17-4 stainless and black nitride treated; standard on all OPF-G6 plates.
- Four recoil lugs — All four lug holes of the DeltaPoint Pro footprint are supported.
- Two-piece front fence — The Gen 6 pocket is shorter than the Gen 5 MOS, so the front fence is split, with the centre section omitted, rather than raising the plate and the sight.
- Uses the ORS locking features — Contoured underside and rear relief engage the spindle cavity and rear locking tab of the Gen 6 slide.
Compatibility and fitment
- For Glock Gen 6 slides with the Optic Ready System (ORS).
- Sights: fit and function are guaranteed only for the Leupold DeltaPoint Pro and EOTech EFLX series. It has not been tested on other DeltaPoint Pro footprint sights, whose dimensions vary.
- Vortex Defender sights sit noticeably looser on this plate than the DeltaPoint Pro and EFLX, and Forward Controls Design states that compatibility with the Defender XT and ST depends on the production batch.
- Sight screws are not included. Install the sight with the M4 screws that came with it and use the sight manufacturer's torque value. The slide's two larger, closer-set holes are the M4 holes for DeltaPoint Pro footprint sights.
- Use the long M4-0.7 × 15.8 mm screws only with a genuine Leupold DeltaPoint Pro; they are too long for any other sight.
- Backup sights: the DeltaPoint Pro needs a front sight height of at least 0.407 in. For the EFLX, 0.315 in works but sits very low; 0.350 in and 0.385 in are recommended.
- Depending on pocket depth, plate thickness and the sight, a gap of less than 0.001 in can appear under the sight. It is cosmetic and has no effect on function.
- Installation: insert the rear of the plate into the rear of the ORS pocket at an angle, confirm the slide's locking tab has engaged the pocket in the plate, then rotate the front down. A firm press on the front may be needed to seat the plate fully.
Technical specifications
| Material | 17-4 stainless steel |
| Finish | Black nitride |
| Sight torque — Leupold DeltaPoint Pro | 25 in·lb (2.8 N·m) |
| Country of manufacture | USA |
Model information
| Brand | Forward Controls Design |
| Model | OPF-G6, DPP — Glock Gen 6 ORS plate for Leupold DeltaPoint Pro / EOTech EFLX |
| MPN | OPF-G6, DPP |